Visa fullständig version : Mini Hobby gear & door computer sequencer
Hej!
Jag har en Mini Hobby gear & door computer sequencer som jag tänkte använda till min J21R,
Men jag kan inte hitta manualen till den och då kan jag inte programera den.:(
Är det någon som har manualen till till den och kan hjälpa mig
Kan det här vara till hjälp?
This device only consumes 30 ma and it's a small package. It uses the gear ATV to set the travel of the gear and doors servos one time, the unit will memorize the data that way gear up and down is only required to initiate the sequence.
Every time you turn on the receiver with the TX on, the unit will initiate the sequence accordingly with the gear selector s/w position and if during the transition the gear s/w is changed, the unit first finishes the cycle then initiates the new command , that way it prevents door and gear miss sequence that some times ends with damaging results.
If you turn on the RX only, the unit will stay in the last position that you previously had set, it means no output to the servos or (MHV) until you turn on the TX.
Hittade det här: http://www.minihobby.com/electronics/mhgdc.htm
Kan det här vara till hjälp?
This device only consumes 30 ma and it's a small package. It uses the gear ATV to set the travel of the gear and doors servos one time, the unit will memorize the data that way gear up and down is only required to initiate the sequence.
Every time you turn on the receiver with the TX on, the unit will initiate the sequence accordingly with the gear selector s/w position and if during the transition the gear s/w is changed, the unit first finishes the cycle then initiates the new command , that way it prevents door and gear miss sequence that some times ends with damaging results.
If you turn on the RX only, the unit will stay in the last position that you previously had set, it means no output to the servos or (MHV) until you turn on the TX.
Hittade det här: http://www.minihobby.com/electronics/mhgdc.htm
Det där har jag också sett men det är bara funktionen på den, inte hur man programerar den,
Tex, landställslucka öppnas-vänta 2 sek-landställ går in-vänta 1sek-landställslucka stängs, typ viggen
eller, landställ går in-vänta 4 sek -landställslucka stängs, typ J21
Tack i alla fall Mr J
Hej!
Jag har en Mini Hobby gear & door computer sequencer som jag tänkte använda till min J21R,
Men jag kan inte hitta manualen till den och då kan jag inte programera den.:(
Är det någon som har manualen till till den och kan hjälpa mig
ja va ska man säga om detta då:banghead:
Trodde en Öviksbo i din kaliber fixade detta enklet men se där även du gick bet o jag sitter nu och ler brett:sarcastic::sarcastic:
kanske får du skicka den till Småland så ska vi fixa till detta lilla bekymret åt dig..yehhh
ja va ska man säga om detta då:banghead:
Trodde en Öviksbo i din kaliber fixade detta enklet men se där även du gick bet o jag sitter nu och ler brett:sarcastic::sarcastic:
kanske får du skicka den till Småland så ska vi fixa till detta lilla bekymret åt dig..yehhh
Ja nu sitter jag också och ler brett och försöker komma på nån dräpande komentar åt dig:sarcastic: men jag kommer inte på nåt som inte sagts åt dig tidigare:banghead: så vi får väl hoppas att våra vänner har nått att tillägga då,
Kontakta tillverkaren/leverantören:
By Phone
http://www.minihobby.com/images/phone.gif
(954) 746-3094
By Mail
http://www.minihobby.com/images/usmailbox.gif
4851 NW 103rd Ave. Suite #52
Sunrise, FL 33351
By Email
http://www.minihobby.com/images/email.gif
minihobby@compuserve.com (minihobby@compuserve.com)
Kontakta tillverkaren/leverantören:
By Phone
http://www.minihobby.com/images/phone.gif
(954) 746-3094
By Mail
http://www.minihobby.com/images/usmailbox.gif
4851 NW 103rd Ave. Suite #52
Sunrise, FL 33351
By Email
http://www.minihobby.com/images/email.gif
minihobby@compuserve.com (minihobby@compuserve.com)
jisses det svaret hette duga måste ju va en Smålänning som skrivit det:lollypop:
Snickarjävel´n
2009-12-06, 20:06
ja va ska man säga om detta då:banghead:
Trodde en Öviksbo i din kaliber fixade detta enklet men se där även du gick bet o jag sitter nu och ler brett:sarcastic::sarcastic:
kanske får du skicka den till Småland så ska vi fixa till detta lilla bekymret åt dig..yehhh
kan ni inte fixa så vinkeln på sidrodret följer höjdrodret vid full läge så ska ni nog in åta er nått mer invecklat :sarcastic::icon_butt:
Kontakta tillverkaren/leverantören:
By Phone
http://www.minihobby.com/images/phone.gif
(954) 746-3094
By Mail
http://www.minihobby.com/images/usmailbox.gif
4851 NW 103rd Ave. Suite #52
Sunrise, FL 33351
By Email
http://www.minihobby.com/images/email.gif
minihobby@compuserve.com (minihobby@compuserve.com)
Är redan gjort med email!
Men har man tur kanske man får svar snabbare härifrån.
Powered by vBulletin® Version 4.2.5 Copyright © 2024 vBulletin Solutions, Inc. All rights reserved.